|
| |
ST-1133A (94354-133) Swift AT (IDE)
+---\
| O | 5
| O | G +-+ Some have
| O | G AT (IDE) Cable | +- these pins
| O | 12 1+........................+ o o o o o(o o)
+---/ ........................ o o o o o(o o)
-------------------------------------------------------
1 2 3 4 5 6 7
ON OFF | | | | | +++
1 Slave Master --+ | | | | |
2 5 Heads 7/9 Heads ----+ | | | |
3 Slave installed Slave not inst. ------+ | | |
4 7 byte ECC 4 byte ECC --------+ | |
5 Factory test Normal Oper. ----------+ |
6/7 Some PWA's have these pins, factory use -------+
ST-1133A
94354-133 Swift
UNFORMATTED CAPACITY (MB) ________________133
FORMATTED CAPACITY (36 SECTORS) (MB) _____117
ACTUATOR TYPE ____________________________VOICE COIL
TRACKS ___________________________________6,360
CYLINDERS ________________________________1,272
HEADS ____________________________________5
DISCS ____________________________________3
MEDIA TYPE _______________________________THIN FILM
RECORDING METHOD _________________________RLL
TRANSFER RATE (mbytes/sec) _______________1.25
SPINDLE SPEED (RPM) ______________________3,600
BUFFER ___________________________________32 or 64 Kbyte
Read Look-Ahead, Non-Adaptive,
Single-Segmented
INTERFACE ________________________________AT BUS
TPI (TRACKS PER INCH) ____________________1,350
BPI (BITS PER INCH) ______________________28,103
AVERAGE ACCESS (ms) ______________________15
SINGLE TRACK SEEK (ms) ___________________4
MTBF (power-on hours) ____________________150,000
POWER REQUIREMENTS: +12V START-UP (amps) _2.5
+12V TYPICAL (amps) __0.7
+5V START-UP (amps) __0.75
+5V TYPICAL (amps) ___0.4
TYPICAL (watts) ______11
MAXIMUM (watts) ______33.75
BUFFERED STEP PULSE RATE (micro sec) _____6-200
WRITE PRECOMP (cyl) ______________________N/A
REDUCED WRITE CURRENT (cyl) ______________N/A
LANDING ZONE (cyl) _______________________AUTO PARK
IBM AT DRIVE TYPE ________________________*
* MAY REQUIRE FORMATTING AND PARTITIONING SOFTWARE. ALSO, CHECK TO
SEE IF YOUR CMOS SETUP HAS A "CUSTOM" OR "USER DEFINABLE" DRIVE TYPE
AVAILABLE. (see below)
Possible translation: 636 cyl, 10 heads, 36 sectors = 117,227,520
Possible translation: 477 cyl, 8 heads, 60 sectors = 117,227,520
Possible translation: 962 cyl, 14 heads, 17 sectors = 117,225,472
Possible translation: 629 cyl, 14 heads, 26 sectors = 117,225,472
Note: A "custom" or "user-definded" CMOS drivetype may ask for a
numerical value for the Write Precompensation cylinder and for the
Landing Zone cylinder. A basic rule-of-thumb for drive models that do
not require the old Write Precomp technique or a Landing Zone because
they are Auto-Parking is to add 1 to the cylinder value being used. As
an example: If cylinders equaled 820, then both Write Precomp and
Landing Zone would be entered as 821. Some BIOS will convert this to
65535 or -1, which are functionally equivalent to "none (not used)".
PHYSICAL/LOGICAL equivalent to NATIVE/TRANSLATION
Already low-level formatted at the factory.
Since a User-definable or Custom translation geometry may be used, it
is imperative that the values be written down and kept with your
permanent records for retrieval in the event of CMOS battery failure.
Swift Remote LED Option
Front View of Drive Without the Plastic Bezel
+---+---+
| A | B | B = Anode
+---+---+ D = Cathode
| C | D |
...-----------------+---+---+-----P-W-A---...
ø Default jumper at C-D for LED mounted on drive PWA
ø To use remote LED, remove jumper and extend B (Anode)
and D (Cathode).
ø Swift LED kit 75912397 allows connection to a remote LED
ø Swift LED kit 95913369 has an LED for attachment to the
system front bezel or a 5.25-inch frame kit
Seagate reserves the right to change, without notice, product
offerings or specifications. (6/26/90) |