|
| |
ST-3096A
4-pin DC
3-pin DC Power
Power +---------- ---------+/-4-3-2-1-\
-+-5-G-12++::::::::::.::::::::1+| 0 0 0 0 +-
| 0 0 0 |+----------+---------++-5-G-G-12+
+-1-2-3-+ (pin-20 missing
for keying purposes)
User Configuration Block
| (located behind 3-pin DC)
+-------+------------------
| 1= On, 0= Off
(back of drive) 2 o-o 1 --- Life Test (do not use)
4 o-o 3 --- Master on (Slave off)--- 1 1 0
6 o-o 5 --- Slave Present ---------- 0 1 0
8 o-o 7 --- Reserved
(front of drive) 10 o-o 9 --- Active LED S M S
i a l
n s a
g t v
l e e
e r
ST-3096A
UNFORMATTED CAPACITY (MB) ________________N/A
FORMATTED CAPACITY (xx/17 SECTORS) (MB) __89.2
ACTUATOR TYPE ____________________________STRAIGHT ARM
TRACKS ___________________________________
CYLINDERS __PHYSICAL/LOGICAL______________xx/1024
HEADS ______PHYSICAL/LOGICAL______________3/10
DISCS (3.5 in) ___________________________2
MEDIA TYPE _______________________________THIN FILM
RECORDING METHOD _________________________RLL (2,7)
TRANSFER RATE INTERNAL (mbits/sec) _______up to 15
SPINDLE SPEED (RPM) ______________________3,211
AVERAGE LATENCY (mSEC) ___________________9.34
BUFFER ___________________________________32 KByte SeaCache
INTERFACE ________________________________AT BUS
SECTORS PER DRIVE ________________________174,080
TPI (TRACKS PER INCH) ____________________1,792
BPI (BITS PER INCH) ______________________31,005
AVERAGE ACCESS (ms) ______________________14
SINGLE TRACK SEEK (ms) ___________________3
MAX FULL SEEK (ms) _______________________22
MTBF (power-on hours) ____________________150,000
POWER REQUIREMENTS: +12V START-UP (amps) _0.9
POWER MANAGEMENT (Watts):
ACTIVE _______________5.3
IDLE _________________2.1
STANDBY ______________0.7
SLEEP ________________0.7
WRITE PRECOMP (cyl) ______________________N/A
REDUCED WRITE CURRENT (cyl) ______________N/A
LANDING ZONE (cyl) _______________________AUTO PARK
IBM AT DRIVE TYPE ________________________*
Physical:
Height (inches/mm): 1.00/25.4
Width (inches/mm): 4.02/102.1
Depth (inches/mm): 5.77/146.6
Weight (lbs/kg): 1.3/0.59
* MAY REQUIRE FORMATTING AND PARTITIONING SOFTWARE. ALSO, CHECK TO
SEE IF YOUR CMOS SETUP HAS A "CUSTOM" OR "USER DEFINABLE" DRIVE TYPE
AVAILABLE. (see below)
Possible translation: 1024 cyl, 10 heads, 17 sectors = 89,128,960
Possible translation: 836 cyl, 8 heads, 26 sectors = 89,030,656
Note: A "custom" or "user-definded" CMOS drivetype may ask for a
numerical value for the Write Precompensation cylinder and for the
Landing Zone cylinder. A basic rule-of-thumb for drive models that do
not require the old Write Precomp technique or a Landing Zone because
they are Auto-Parking is to add 1 to the cylinder value being used. As
an example: If cylinders equaled 820, then both Write Precomp and
Landing Zone would be entered as 821. Some BIOS will convert this to
65535 or -1, which are functionally equivalent to "none (not used)".
PHYSICAL/LOGICAL equivalent to NATIVE/TRANSLATION
ZBR = Zone Bit Recording = Variable sectors per track
Already low-level formatted at the factory.
Since a User-definable or Custom translation geometry may be used, it
is imperative that the values be written down and kept with your
permanent records for retrieval in the event of CMOS battery failure.
Seagate reserves the right to change, without notice, product
offerings or specifications. (5/13/91) |