|
| |
ST-41600N (97501-16G) Elite-1 FH Fast SCSI-2
+- This T-RES only on Differential model
Spindle Sync + | +- Terminator Power Source (see below)--+
+4--1--+ +--*---1 4o|o3 +------1 |
|o oo A +-|----+ 2o o1 +--|---+ |
o o o o o |o oo B +Terminator DIPS+ Power o o o o |
o o o o o +------++-------------------------+ +12-G-G-5-+ o o o o |
-+-+-+-+-+--P-W-A---+::::::::::::::::::::::::1+--+ 0 0 0 0 +-+-+-+-+-- |
4 2 1 | | +-------------------------+ \---------/ | | | | |
--+-- | | SCSI Cable Connector | | | | |
| | | | | | | |
| | +-- Master off/Slave on - Spindle Sync | | | | |
| +---- Write Protect option enable | | | | |
+-------- SCSI ID | | | | |
Spinup Delay (10 secs * ID) -+ | | | |
Motor Start option enable ---+ | | |
Parity check DISable -----+ | |
Sweep Cycle enable -------+ |
|
|
+----------------------------------+ |
| Terminator Power Source Options +----------------------------------------+
+----------------------------------+-----------------------------------+
| 2 & 4 - Initiator supplies power over the SCSI Bus for terminators. |
| Drive supplies no terminator power. |
| 1 & 2 - Drive supplies power for its own terminator resistor-paks |
| but not to SCSI Bus. This is the factory setting. |
| 1 & 3 |
| AND - Drive supplies power for external terminator at end of the |
| 2 & 4 daisy chain. Terminator resistor-paks must be removed. |
| This option is recommended only for last drive on daisy |
| chain. (This option only on Single-Ended drives) |
+----------------------------------------------------------------------+
ST-41600N
Elite-1 FH
UNFORMATTED CAPACITY ____ ________________1,600,930,800
FORMATTED CAPACITY (xx SECTORS) ____ _____1,370,545,152 **
AVERAGE SECTORS PER TRACK (with spares)___74.945
ACTUATOR TYPE ____________________________STRAIGHT ARM
TRACKS/USER ______________________________35,717/35,666
CYLINDERS/USER____________________________2,101/2,098
HEADS ____________________________________17
DISCS ____________________________________10
MEDIA TYPE _______________________________THIN FILM
HEAD TYPE ________________________________THIN FILM
RECORDING METHOD _________________________ZBR RLL (2,7)
INTERNAL TRANSFER RATE (mbits/sec) _______26 to 36
EXTERNAL TRANSFER RATE (mbytes/sec) ______5
SPINDLE SPEED (RPM) ______________________5,400
AVERAGE LATENCY (mSEC) ___________________5.56
COMMAND OVERHEAD (msec) __________________<0.5
BUFFER ___________________________________192 Kbyte
Read Look-Ahead, Adaptive, Multi-Segmented
Cache
INTERFACE ________________________________Fast SCSI-2
BYTES PER TRACK __________________________36,400 to 50,400
SECTORS PER DRIVE ________________________2,768,896
BYTES PER CYLINDER _______________________618,800 to 856,800
TPI (TRACKS PER INCH) ____________________
BPI (BITS PER INCH) ______________________
AREAL DENSITY ____________________________
AVERAGE ACCESS (ms) ______________________11.5
SINGLE TRACK SEEK (ms) ___________________1.7
MAX FULL SEEK (ms) _______________________22.5
MTBF (power-on hours) Class A Room _______250,000
MTBF (power-on hours) Office _____________150,000
POWER DISSIPATION (watts/BTU) ____________
POWER REQUIREMENTS: Single-ended/Differential
+12V START-UP (amps) _2.2/3.2
+12V TYPICAL (amps) __1.8/1.8
+5V START-UP (amps) __2.1/2.9
+5V TYPICAL (amps) ___2.0/2.3
TYPICAL (watts) ______31.6/33.1
MAXIMUM (watts) ______36.9/39.4
LANDING ZONE (cyl) _______________________AUTO PARK
USER MANUAL PART NUMBER __________________83327460
REFERENCE MANUAL PART NUMBER _____________83327470
IBM AT DRIVE TYPE ________________________0 or NONE
OTHER ____________________________________
ZBR = Zone Bit Recording = Variable sectors per track
** Already low-level formatted at the factory with six spare sectors
per cylinder, one spare cylinders/unit, one system cylinder/unit, and
one diagnostic cylinder/unit.
Physical:
Height (inches/mm): 3.25/82.6
Width (inches/mm): 5.75/146.1
Depth (inches/mm): 8.0/203
Weight (lbs/kg): 7.8/3.6
Seagate reserves the right to change, without notice, product
offerings or specifications. (10/28/91) |